All Braindump2go PDF Dumps and VCE Dumps

Braindump2go Latest and Hottest Dumps with PDF and VCE are free Shared Here!

300-710 Exam Dumps300-710 Exam Questions300-710 PDF Dumps300-710 VCE DumpsCisco

[2025-December-New]Braindump2go 300-710 PDF and VCE Dumps Free Download[Q265-Q320]

admin

2025/December Latest Braindump2go 300-710 Exam Dumps with PDF and VCE Free Updated Today! Following are some new Braindump2go 300-710 Real Exam Questions!

QUESTION 265
An organization is implementing Cisco FTD using transparent mode in the network. Which rule in the default Access Control Policy ensures that this deployment does not create a loop in the network?

A. ARP inspection is enabled by default.
B. Multicast and broadcast packets are denied by default.
C. STP BPDU packets are allowed by default.
D. ARP packets are allowed by default.

Answer: C
Explanation:
https://www.cisco.com/c/en/us/td/docs/security/firepower/630/configuration/guide/fpmc-config-guide-v63/transparent_or_routed_firewall_mode_for_firepower_threat_defense.html

QUESTION 266
An organization is installing a new Cisco FTD appliance in the network. An engineer is tasked with configuring access between two network segments within the same IP subnet. Which step is needed to accomplish this task?

A. Assign an IP address to the Bridge Virtual Interface.
B. Permit BPDU packets to prevent loops.
C. Specify a name for the bridge group.
D. Add a separate bridge group for each segment.

Answer: A

QUESTION 267
When a Cisco FTD device is configured in transparent firewall mode, on which two interface types can an IP address be configured? (Choose two.)

A. Diagnostic
B. EtherChannel
C. BVI
D. Physical
E. Subinterface

Answer: AC

QUESTION 268
An administrator needs to configure Cisco FMC to send a notification email when a data transfer larger than 10 MB is initiated from an internal host outside of standard business hours. Which Cisco FMC feature must be configured to accomplish this task?

A. file and malware policy
B. application detector
C. intrusion policy
D. correlation policy

Answer: D
Explanation:
Correlation policies allow you to correlate security events based on various criteria, including time of day, user, source/destination IP address, and more. When the specified criteria are met, the correlation policy can trigger a response action, such as sending an email notification.

QUESTION 269
A security engineer is adding three Cisco FTD devices to a Cisco FMC. Two of the devices have successfully registered to the Cisco FMC. The device that is unable to register is located behind a router that translates all outbound traffic to the router’s WAN IP address. Which two steps are required for this device to register to the Cisco FMC? (Choose two.)

A. Reconfigure the Cisco FMC lo use the device’s private IP address instead of the WAN address.
B. Configure a NAT ID on both the Cisco FMC and the device.
C. Add the port number being used for PAT on the router to the device’s IP address in the Cisco FMC.
D. Reconfigure the Cisco FMC to use the device’s hostname instead of IP address.
E. Remove the IP address defined for the device in the Cisco FMC.

Answer: BE

QUESTION 270
An engineer defines a new rule while configuring an Access Control Policy. After deploying the policy, the rule is not working as expected and the hit counters associated with the rule are showing zero.
What is causing this error?

A. Logging is not enabled for the rule.
B. The rule was not enabled after being created.
C. The wrong source interface for Snort was selected in the rule.
D. An incorrect application signature was used in the rule.

Answer: D

QUESTION 271
A network administrator is configuring a site-to-site IPsec VPN to a router sitting behind a Cisco FTD. The administrator has configured an access policy to allow traffic to this device on UDP 500, 4500, and ESP VPN traffic is not working. Which action resolves this issue?

A. Set the allow action in the access policy to trust.
B. Enable IPsec inspection on the access policy.
C. Modify the NAT policy to use the interface PAT.
D. Change the access policy to allow all ports.

Answer: C
Explanation:
In a site-to-site IPsec VPN configuration where one router is behind a Cisco FTD (Firepower Threat Defense) firewall, proper NAT traversal is critical.
Even if you’ve allowed UDP 500 (ISAKMP), UDP 4500 (NAT-T), and ESP (IP protocol 50) in the access policy, NAT can still break the VPN unless handled properly.

QUESTION 272
An engineer is configuring two new Cisco FTD devices to replace the existing high availability firewall pair in a highly secure environment. The information exchanged between the FTD devices over the failover link must be encrypted. Which protocol supports this on the Cisco FTD?

A. IPsec
B. SSH
C. SSL
D. MACsec

Answer: A

QUESTION 273
An engineer is troubleshooting HTTP traffic to a web server using the packet capture tool on Cisco FMC. When reviewing the captures, the engineer notices that there are a lot of packets that are not sourced from or destined to the web server being captured. How can the engineer reduce the strain of capturing packets for irrelevant traffic on the Cisco FTD device?

A. Use the host filter in the packet capture to capture traffic to or from a specific host.
B. Redirect the packet capture output to a .pcap file that can be opened with Wireshark.
C. Use the -c option to restrict the packet capture to only the first 100 packets.
D. Use an access-list within the packet capture to permit only HTTP traffic to and from the web server.

Answer: A

QUESTION 274
A security engineer needs to configure a network discovery policy on a Cisco FMC appliance and prevent excessive network discovery events from overloading the FMC database. Which action must be taken to accomplish this task?

A. Change the network discovery method to TCP/SYN.
B. Configure NetFlow exporters for monitored networks.
C. Monitor only the default IPv4 and IPv6 network ranges.
D. Exclude load balancers and NAT devices in the policy.

Answer: D

QUESTION 275
An engineer is setting up a remote access VPN on a Cisco FTD device and wants to define which traffic gets sent over the VPN tunnel. Which named object type in Cisco FMC must be used to accomplish this task?

A. split tunnel
B. crypto map
C. access list
D. route map

Answer: C
Explanation:
You can specify the access list in Objects that needs to be used for interesting traffic.

QUESTION 276
Which process should be checked when troubleshooting registration issues between Cisco FMC and managed devices to verify that secure communication is occurring?

A. fpcollect
B. dhclient
C. sfmgr
D. sftunnel

Answer: D

QUESTION 277
An engineer needs to configure remote storage on Cisco FMC. Configuration backups must be available from a secure location on the network for disaster recovery. Reports need to back up to a shared location that auditors can access with their Active Directory logins. Which strategy must the engineer use to meet these objectives?

A. Use SMB for backups and NFS for reports.
B. Use NFS for both backups and reports.
C. Use SMB for both backups and reports.
D. Use SSH for backups and NFS for reports.

Answer: C
Explanation:
You cannot send backups to one remote system and reports to another, but you can choose to send either to a remote system and store the other on the Firepower Management Center.
https://www.cisco.com/c/en/us/td/docs/security/firepower/640/configuration/guide/fpmc-config-guide-v64/system_configuration.html#ID-2241-00000551

QUESTION 278
Which firewall design will allow it to forward traffic at layers 2 and 3 for the same subnet?

A. Cisco Firepower Threat Defense mode
B. routed mode
C. Integrated routing and bridging
D. transparent mode

Answer: C
Explanation:
Integrated routing and bridging (IRB) is a feature of Cisco Firepower Threat Defense (FTD) that allows the firewall to forward traffic at both layers 2 and 3 for the same subnet. In this mode, the firewall can act as a switch or a bridge to forward traffic at layer 2 and as a router to forward traffic at layer 3. This allows the firewall to maintain full control over the traffic, while still allowing it to forward traffic at both layers.
https://www.cisco.com/c/en/us/td/docs/security/firepower/ftd-config-guide/FTD-Config-Guide-v6/Integrated-Routing-and-Bridging.html

QUESTION 279
Drag and Drop Question
Drag and drop the configuration steps from the left into the sequence on the right to enable external authentication on Cisco FMC to a RADIUS server.

Answer:

Explanation:
https://www.cisco.com/c/en/us/td/docs/security/firepower/623/configuration/guide/fpmc-config-guide-v623/user_accounts_for_management_access.html

QUESTION 280
Drag and Drop Question
A network engineer is deploying a Cisco Firepower 4100 appliance and must configure a multi-instance environment for high availability. Drag and drop the actions from the left into sequence on the right for this configuration.

Answer:

QUESTION 281
A security engineer must configure policies for a recently deployed Cisco FTD. The security policy for the company dictates that when five or more connections from external sources are initiated within 2 minutes, there is cause for concern. Which type of policy must be configured in Cisco FMC to generate an alert when this condition is triggered?

A. application detector
B. access control
C. correlation
D. intrusion

Answer: C

QUESTION 282
A network administrator is reviewing a weekly scheduled attacks risk report and notices a host that is flagged for an Impact 2 attack. Where should the administrator look within Cisco FMC to find out more relevant information about this host and attack?

A. Analysis > Lookup > Whois
B. Analysis > Correlation > Correlation Events
C. Analysis > Hosts > Vulnerabilities
D. Analysis > Hosts > Host Attributes

Answer: B
Explanation:
When a host is flagged for an Impact 2 attack in Cisco FMC (Firepower Management Center), this indicates a moderate threat, meaning the attack was likely successful or could affect a vulnerable host.
To investigate what happened, including details about the attack, source/destination, application, and relevant detection rules, the administrator should review correlation events, which tie together intrusion events, host profiles, and vulnerabilities.
https://www.cisco.com/c/en/us/td/docs/security/firepower/70/configuration/guide/fpmc-config-guide-v70/correlation_and_compliance_events.html

QUESTION 283
A consultant is working on a project where the customer is upgrading from a single Cisco Firepower 2130 managed by FDM to a pair of Cisco Firepower 2130s managed by FMC for high availability. The customer wants the configuration of the existing device being managed by FDM to be carried over to FMC and then replicated to the additional device being added to create the high availability pair. Which action must the consultant take to meet this requirement?

A. The current FDM configuration must be configured by hand into FMC before the devices are registered.
B. The current FDM configuration must be migrated to FMC using the Secure Firewall Migration Tool.
C. The FTD configuration must be converted to ASA command format, which can then be migrated to FMC.
D. The current FDM configuration will be converted automatically into FMC when the device registers.

Answer: B

QUESTION 284
A network administrator must create an EtherChannel interface on a new Cisco Firepower 9300 appliance registered with an FMC for high availability. Where must the administrator create the EtherChannel interface?

A. FMC GUI
B. FMC CLI
C. FTD CLI
D. FXOS CLI

Answer: D

QUESTION 285
A network administrator is reviewing a monthly advanced malware risk report and notices a host that is listed as CnC Connected. Where must the administrator look within Cisco FMC to further determine if this host is infected with malware?

A. Analysis > Hosts > Indications of Compromise
B. Analysis > Hosts > Host Attributes
C. Analysis > Files > Malware Events
D. Analysis > Files > Network File Trajectory

Answer: A

QUESTION 286
An engineer is configuring a Cisco FTD device to place on the Finance VLAN to provide additional protection for company financial data. The device must be deployed without requiring any changes on the end user workstations, which currently use DHCP to obtain an IP address. How must the engineer deploy the device to meet this requirement?

A. Deploy the device in transparent mode and enable the DHCP Server feature.
B. Deploy the device in routed mode and enable the DHCP Relay feature.
C. Deploy the device in transparent mode and allow DHCP traffic in the access control policies.
D. Deploy the device in routed mode and allow DHCP traffic in the access control policies.

Answer: C
Explanation:
For example, by using an access rule, you can allow DHCP traffic (instead of the unsupported DHCP relay feature) or multicast traffic such as that created by IP/TV. You can also establish routing protocol adjacencies through a transparent firewall; you can allow OSPF, RIP, EIGRP, or BGP traffic through based on an access rule. Likewise, protocols like HSRP or VRRP can pass through the FTD device.

QUESTION 287
Which default action setting in a Cisco FTD Access Control Policy allows all traffic from an undefined application to pass without Snort inspection?

A. Network Discovery Only
B. Inherit from Base Policy
C. Intrusion Prevention
D. Trust All Traffic

Answer: D

QUESTION 288
An engineer plans to reconfigure an existing Cisco FTD from transparent mode to routed mode. Which additional action must be taken to maintain communication between the two network segments?

A. Assign a unique VLAN ID for the interface in each segment.
B. Update the IP addressing so that each segment is a unique IP subnet.
C. Configure a NAT rule so that traffic between the segments is exempt from NAT.
D. Deploy inbound ACLs on each interface to allow traffic between the segments.

Answer: B

QUESTION 289
Network users are experiencing intermittent issues with internet access. An engineer identified that the issue is being caused by NAT exhaustion. How must the engineer change the dynamic NAT configuration to provide internet access for more users without running out of resources?

A. Convert the dynamic auto NAT rule to dynamic manual NAT.
B. Add an identity NAT rule to handle the overflow of users.
C. Configure fallthrough to interface PAT on the Advanced tab.
D. Define an additional static NAT for the network object in use.

Answer: C

QUESTION 290
An engineer is configuring a custom intrusion rule on Cisco FMC. The engineer needs the rule to search the payload or stream for the string “|44 78 97 13 2 0A|”. Which keyword must the engineer use with this string to create an argument for packet inspection?

A. protected_content
B. content
C. data
D. metadata

Answer: B

QUESTION 291
An engineer must investigate a connectivity issue from an endpoint behind a Cisco FTD device and a public DNS server. The endpoint cannot perform name resolution queries. Which action must the engineer perform to troubleshoot the issue by simulating real DNS traffic on the Cisco FTD while verifying the Snort verdict?

A. Use the Capture w/Trace wizard in Cisco FMC.
B. Run the system support firewall-engine-debug command from the FTD CLI.
C. Create a Custom Workflow in Cisco FMC.
D. Perform a Snort engine capture using tcpdump from the FTD CLI.

Answer: A
Explanation:
To trace a real packet is very useful to troubleshoot connectivity issues. It allows you to see all the internal checks that a packet goes through. Add the trace detail keywords and specify the number of packets that you want to be traced. By default, the FTD traces the first 50 ingress packets.
In this case, enable capture with trace detail for the first 100 packets that FTD receives on the INSIDE interface:
> capture CAPI2 interface INSIDE trace detail trace-count 100 match icmp host 192.168.103.1 host 192.168.101.1

QUESTION 292
What is a limitation to consider when running a dynamic routing protocol on a Cisco FTD device in IRB mode?

A. Only link-stale routing protocols are supported.
B. Only distance vector routing protocols are supported.
C. Only EtherChannel interfaces are supposed.
D. Only nonbridge interfaces are supported.

Answer: D

QUESTION 293
An engineer must integrate a third-party security intelligence feed with Cisco Secure Firewall Management Center. Secure Firewall Management Center is running Version 6.2.3 and has 8 GB of memory.
Which two actions must be taken to implement Threat Intelligence Director? (Choose two.)

A. Add a TAXII server.
B. Add the URL of the TAXII server.
C. Upgrade to version 6.6.
D. Enable REST API access.
E. Add 7 GB of memory.

Answer: DE
Explanation:
You can host TID on physical and virtual Firepower Management Centers:
– running Version 6.2.2 or later of the Firepower System.
– configured with a minimum of 15 GB of memory.
– configured with REST API access enabled.
https://www.cisco.com/c/en/us/td/docs/security/firepower/623/configuration/guide/fpmc-config-guide-v623/cisco_threat_intelligence_director__tid_.html

QUESTION 294
An engineer is configuring a custom application detector for HTTP traffic and wants to import a file that was provided by a third party. Which type of flies are advanced application detectors creates and uploaded as?

A. Perl script
B. NBAR protocol
C. LUA script
D. Python program

Answer: C

QUESTION 295
Which action must be taken to configure an isolated bridge group for IRB mode on a Cisco Secure Firewall device?

A. Add the restricted segment to the ACL.
B. Leave BVI interface name empty.
C. Define the NAT pool for the blocked traffic.
D. Remove the route from the routing table.

Answer: B
Explanation:
To configure an isolated bridge group for Integrated Routing and Bridging (IRB) mode on a Cisco Secure Firewall device, the action to take is to leave the BVI (Bridge Virtual Interface) interface name empty. This ensures that the bridge group operates in an isolated manner, where Layer 3 routing is not applied to the bridged interfaces, effectively isolating the traffic within the bridge group.
Steps:
Access the firewall’s configuration interface.
Configure the bridge group interfaces.
Ensure that the BVI interface name is left empty to isolate the bridge group.
This configuration prevents Layer 3 routing for the isolated bridge group, ensuring that traffic remains contained within the bridge group.

QUESTION 296
When an engineer captures traffic on a Cisco FTD to troubleshoot a connectivity problem, they receive a large amount of output data in the GUI tool. The engineer found that viewing the Captures this way is time-consuming and difficult to son and filter.
Which file type must the engineer export the data in so that it can be reviewed using a tool built for this type of analysis?

A. NetFlow v9
B. PCAP
C. NetFlow v5
D. IPFIX

Answer: B

QUESTION 297
An engineer must deploy a Cisco FTD device. Management wants to examine traffic without requiring network changes that will disrupt end users. Corporate security policy requires the separation of management traffic from data traffic and the use of SSH over Telnet for remote administration. How must the device be deployed to meet these requirements?

A. in routed mode with a diagnostic interface
B. in transparent mode with a management Interface
C. in transparent made with a data interface
D. in routed mode with a bridge virtual interface

Answer: B

QUESTION 298
A network administrator reviews the attack risk report and notices several low-impact attacks. What does this type of attack indicate?

A. All attacks are listed as low until manually recategorized.
B. The host is not vulnerable to those attacks.
C. The host is not within the administrator’s environment.
D. The attacks are not dangerous to the network.

Answer: B

QUESTION 299
What is a limitation to consider when running a dynamic routing protocol on a Cisco Secure Firewall Threat Defense device in IRB mode?

A. Only link-state routing protocols are supported.
B. Only nonbridge interfaces are supported.
C. Only EtherChannel interfaces are supported.
D. Only distance vector routing protocols are supported.

Answer: B

QUESTION 300
An engineer is configuring URL filtering for a Cisco FTD device in Cisco FMC. Users must receive a warning when they access http://www.badadultsite.com with the option of continuing to the website if they choose to. No other websites should be blocked. Which two actions must the engineer take to meet these requirements? (Choose two.)

A. On the HTTP Responses tab of the access control policy editor, set the Interactive Block Response Page to System-provided.
B. Configure the default action for the access control policy to Interactive Block.
C. Configure an access control rule that matches an URL object for http://www.badadultsite.com/ and set the action to Interactive Block.
D. Configure an access control rule that matches the Adult URL category and set the action to Interactive Block.
E. On the HTTP Responses tab of the access control policy editor, set the Block Response Page to Custom.

Answer: AC
Explanation:
To configure URL filtering such that users receive a warning when they access a specific website (e.g., http://www.badadultsite.com) and have the option to continue to the site, the engineer needs to perform the following actions:
Configure an access control rule:
Create a URL object for http://www.badadultsite.com.
Set the action for this URL object to “Interactive Block,” which prompts the user with a warning and allows them to proceed if they choose to.
Set the Interactive Block Response Page:
Navigate to the HTTP Responses tab in the access control policy editor. Set the Interactive Block Response Page to “System-provided” to ensure that users see the default warning page provided by Cisco Secure Firewall Management Center. These actions ensure that only the specified website triggers an interactive block, while other websites are not blocked.

QUESTION 301
The security engineer reviews the syslog server events of an organization and sees many outbound connections to malicious sites initiated from hosts running Cisco Secure Endpoint. The hosts are on a separate network from the Cisco FTD device. Which action blocks the connections?

A. Modify the policy on Cisco Secure Endpoint to enable DFC.
B. Modify the access control policy on the Cisco FMC to block malicious outbound connections
C. Add the IP addresses of the malicious sites to the access control policy on the Cisco FMC
D. Add a Cisco Secure Endpoint policy with the Tetra and Spero engines enabled

Answer: A
Explanation:
Cisco Secure Endpoint with DFC enabled can block malicious outbound connections by correlating device network flows and enforcing blocks directly on the endpoints, even if those endpoints are on a separate network from the Cisco Firepower Threat Defense (FTD) device.
Modifying the access control policy on Cisco FMC (Firepower Management Center) or adding IP addresses to FMC policies would not block connections from hosts on a separate network that the FMC/FTD does not directly control.
Enabling DFC in Secure Endpoint allows the endpoint agent to block connections to malicious IPs or domains based on threat intelligence and policy, which is effective for hosts outside the FTD’s network scope.
https://docs.amp.cisco.com/en/SecureEndpoint/Secure%20Endpoint%20User%20Guide.pdf (page 73)

QUESTION 302
An engineer has been tasked with performing an audit of network objects to determine which objects are duplicated across the various firewall models (Cisco Secure Firewall Threat Defense, Cisco Secure Firewall ASA, and Meraki MX Series) deployed throughout the company. Which tool will assist the engineer in performing that audit?

A. Cisco Firepower Device Manager
B. Cisco Defense Orchestrator
C. Cisco Secure Firewall Management Center
D. Cisco SecureX

Answer: B
Explanation:
Cisco Defense Orchestrator (CDO) is the tool that assists engineers in performing an audit of network projects to determine which objects are duplicated across various firewall models, including Cisco Secure Firewall Threat Defense, Cisco Secure Firewall ASA, and Meraki MX Series. CDO provides a unified management interface for managing multiple security devices and can identify duplicate objects across these devices.
Steps:
Access Cisco Defense Orchestrator.
Connect and synchronize all relevant firewall devices (FTD, ASA, Meraki MX). Use the audit and reporting features in CDO to identify and manage duplicate objects. This helps ensure consistency and efficient management across the organization’s firewall deployments.

QUESTION 303
A network engineer is deploying a pair of Cisco Secure Firewall Threat Defense devices managed by Cisco Secure Firewall Management Center for High Availability. Internet access is a high priority for the business and therefore they have invested in internet circuits from two different ISPs. The requirement from the customer is that internet access must be available to their users even if one of the ISPs is down. Which two features must be deployed to achieve this requirement? (Choose two.)

A. Route Tracking
B. Redundant interfaces
C. EtherChannel interfaces
D. SLA Monitor
E. BGP

Answer: AD
Explanation:
To ensure high availability of internet access when deploying a pair of Cisco Secure Firewall Threat Defense (FTD) devices managed by Cisco Secure Firewall Management Center (FMC), the following features must be deployed:
Route Tracking: This feature monitors the reachability of a specified target (such as an external IP address) through the configured routes. If the route to the target is lost, the FTD can dynamically adjust the routing to use an alternate path, ensuring continuous internet access. SLA Monitor: Service Level Agreement (SLA) monitoring works alongside route tracking to continuously verify the status and performance of the internet links. If the SLA for one of the ISP links fails (indicating the link is down or underperforming), the FTD can switch traffic to the secondary ISP link.
Steps to configure:
In FMC, navigate to Devices > Device Management.
Select the FTD device and configure route tracking to monitor the ISP links. Configure SLA monitors to continuously check the health and performance of the internet circuits. These configurations ensure that internet access remains available to users even if one of the ISPs goes down.

QUESTION 304
A network engineer is planning on replacing an Active/Standby pair of physical Cisco Secure Firewall ASAs with a pair of Cisco Secure Firewall Threat Defense Virtual appliances. Which two virtual environments support the current High Availability configuration? (Choose two.)

A. ESXi
B. Azure
C. Openstack
D. KVM
E. AWS

Answer: AD
Explanation:
https://www.cisco.com/c/en/us/products/collateral/security/firepower-ngfw-virtual/threat-defense-virtual-ngfwv-ds.html

QUESTION 305
A company is deploying AMP private cloud. The AMP private cloud instance has already been deployed by the server administrator. The server administrator provided the hostname of the private cloud instance to the network engineer via email. What additional information does the network engineer require from the server administrator to be able to make the connection to the AMP private cloud in Cisco FMC?

A. SSL certificate for the AMP private cloud instance
B. Username and password to the AMP private cloud instance
C. IP address and port number for the connection proxy
D. Internet access for the AMP private cloud to reach the AMP public cloud

Answer: A
Explanation:
Step 6: Click Browse next to the Certificate Upload Path field to browse to the location of a valid TLS or SSL encryption certificate for the private cloud. For more information, see the AMP private cloud documentation.
https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config-guide-v62/file_policies_and_amp_for_firepower.html

QUESTION 306
A security engineer is deploying Cisco Secure Endpoint to detect a zero day malware attack with an SHA-256 hash of 47ea931f3e9dc23ec0b0885a80663e30ea013d493f8e88224b570a0464084628. What must be configured in Cisco Secure Endpoint to enable the application to take action based on this hash?

A. access control rule
B. correlation policy
C. transform set
D. custom detection list

Answer: D

QUESTION 307
A security engineer must create a malware and file policy on a Cisco Secure Firewall Threat Defense device. The solution must ensure that PDF, DOCX, and XLSX files are not sent to Cisco Secure Malware Analytics. What must be configured to meet the requirements?

A. Spero analysis
B. local malware analysis
C. capacity handling
D. dynamic analysis

Answer: B
Explanation:
To create a malware and file policy on a Cisco Secure Firewall Threat Defense (FTD) device that ensures PDF, DOCX, and XLSX files are not sent to Cisco Secure Malware Analytics, the security engineer must configure local malware analysis. Local malware analysis allows the FTD to inspect and analyze files locally without sending them to the cloud-based Cisco Secure Malware Analytics.
Steps to configure local malware analysis:
In FMC, navigate to Policies > Access Control > Malware & File Policies. Create a new malware and file policy or edit an existing one. Define rules to inspect specific file types, ensuring that PDF, DOCX, and XLSX files are handled locally. Set the action for these file types to “Local Analysis.” Apply the policy to the relevant access control policy. This configuration ensures that the specified file types are analyzed locally, meeting the requirement to avoid sending them to Cisco Secure Malware Analytics.

QUESTION 308
Encrypted Visibility Engine (EVE) is enabled under which tab on an access control policy in Cisco Secure Firewall Management Center?

A. Network Analysis Policy
B. SSL
C. Advanced
D. Security Intelligence

Answer: C
Explanation:
Available under the Advanced tab of the access control policy, to enable or disable EVE.
https://www.cisco.com/c/en/us/td/docs/security/secure-firewall/management-center/snort/720/snort3-configuration-guide-v72/m_encrypted-visibility-engine.pdf

QUESTION 309
An engineer is configuring a Cisco Secure Firewall Threat Defense device managed by Cisco Secure Firewall Management Center. The device must have SSH enabled and be accessible from the inside interface for remote administration. Which type of policy must the engineer configure to accomplish this?

A. platform settings
B. access control
C. prefilter
D. identity

Answer: A
Explanation:
To enable SSH access to a Cisco Secure Firewall Threat Defense (FTD) device from the inside interface for remote administration, the engineer needs to configure a Platform Settings policy in Cisco Secure Firewall Management Center (FMC). The Platform Settings policy allows the configuration of various system-related settings, including enabling SSH, specifying the allowed interfaces, and defining the SSH access parameters.
Steps:
In FMC, navigate to Policies > Access Control > Platform Settings. Create a new Platform Settings policy or edit an existing one.
In the policy settings, go to the SSH section.
Enable SSH and specify the inside interface as the allowed interface for SSH access. Define the SSH parameters such as allowed IP addresses, user credentials, and other security settings.
Save and deploy the policy to the FTD device.
This configuration ensures that SSH access is enabled on the specified interface, allowing secure remote administration.

QUESTION 310
What is the result when two users modify a VPN policy at the same time on a Cisco Secure Firewall Management Center managed device?

A. Both users can edit the policy and the last saved configuration persists.
B. The changes from both users will be merged together into the policy.
C. The first user locks the configuration when selecting edit on the policy.
D. The system prevents modifications to the policy by multiple users.

Answer: A
Explanation:
Two users must not edit a remote access VPN policy at the same time; however, the web interface does not prevent simultaneous editing. If this occurs, the last saved configuration persists.
https://www.cisco.com/c/en/us/td/docs/security/secure-firewall/management-center/device-config/710/management-center-device-config-71/vpn-remote-access.html

QUESTION 311
A network administrator is configuring a BVI interface on a routed FTD. The administrator wants to isolate traffic on the interfaces connected to the bridge group and not have the FTD route this traffic using the routing table. What must be configured?

A. A new VRF must be created for the BVI interface
B. An IP address must be configured on the BVI
C. IP routing must be removed from the physical interfaces connected to the BVI
D. The BVI interface must be configured for transparent mode

Answer: A
Explanation:
https://www.cisco.com/c/en/us/td/docs/security/firepower/660/configuration/guide/fpmc-config-guide-v66/virtual-routing-for-firepower-threat-defense.html

QUESTION 312
Which file format can standard reports from Cisco Secure Firewall Management Center be downloaded in?

A. doc
B. ppt
C. csv
D. xls

Answer: C
Explanation:
Standard reports from Cisco Secure Firewall Management Center can be downloaded in CSV (Comma-Separated Values) format. This format is widely used for data exchange and can be opened in various applications such as Microsoft Excel.
Steps to download reports:
Navigate to Reports > Report Designer in the FMC.
Select or create the report you wish to download.
Choose the CSV format option when exporting the report. This allows the network engineer to analyze and manipulate the report data easily.

QUESTION 313
Remote users who connect via Cisco Secure Client to the corporate network behind a Cisco Secure Firewall Threat Defense device are reporting no audio on calls when calling between remote users using their softphones. These same users can call internal users on the corporate network without any issues. What is the cause of this issue?

A. The hairpinning feature is not available on Cisco Secure Firewall Threat Defense
B. Cisco Secure Firewall Threat Defense needs a NAT policy that allows outside to outside communication
C. The Enable Spoke to Spoke Connectivity through Hub option is not selected on Cisco Secure Firewall Threat Defense
D. Split tunneling is enabled for the Remote Access VPN on Cisco Secure Firewall Threat Defense

Answer: B
Explanation:
https://www.cisco.com/c/en/us/support/docs/security/anyconnect-secure-mobility-client-v4x/220337-troubleshoot-common-anyconnect-communica.html

QUESTION 314
An administrator is configuring the interface of a Cisco Secure Firewall Threat Defense firewall device in a passive IPS deployment. The device and interface have been identified. Which set of configuration steps must the administrator perform next to complete the implementation?

A. Set the interface mode to passive. Associate the interface with a security zone. Enable the interface. Set the MTU parameter.
B. Modify the interface to retransmit received traffic. Associate the interface with a security zone Set the MTU parameter
C. Set the interface mode to passive. Associate the interface with a security zone. Set the MTU parameter. Reset the interface.
D. Modify the interface to retransmit received traffic. Associate the interface with a security zone. Enable the interface. Set the MTU parameter.

Answer: A
Explanation:
In a passive IPS deployment for a Cisco Secure Firewall Threat Defense (FTD) device, the administrator must configure the interface to operate in passive mode. This involves setting the interface mode, associating it with a security zone, enabling the interface, and setting the MTU parameter.
Steps:
Set the interface mode to passive:
In FMC, navigate to Devices > Device Management.
Select the FTD device and configure the relevant interface.
Set the interface mode to “Passive.”
Associate the interface with a security zone:
Create or select an appropriate security zone.
Assign the passive interface to this security zone.
Enable the interface:
Ensure the interface is enabled to receive traffic.
Set the MTU parameter:
Configure the Maximum Transmission Unit (MTU) parameter as required. This ensures that the FTD device can inspect traffic passively without impacting the network flow.

QUESTION 315
Which two statements are valid regarding the licensing model used on Cisco Secure Firewall Threat Defense Virtual appliances? (Choose two.)

A. All licenses support a maximum of 250 VPN peers
B. All licenses support up to 16 vCPUs
C. All licenses require 500G of available storage for the VM
D. Licenses can be used on both physical and virtual appliances
E. Licenses can be used on any supported cloud platform

Answer: DE

QUESTION 316
A company is deploying Cisco Secure Firewall Threat Defense with IPS. What must be implemented in inline mode to pass the traffic without inspection during spikes and ensure that network traffic is kept?

A. Change the interface mode to Routed
B. Select Propagate Link State
C. Increase the MTU to 9000
D. Set the Snort Failsafe option

Answer: D

QUESTION 317
A Cisco Secure Firewall Threat Defense device is configured in inline IPS mode to inspect all traffic that passes through the interfaces in the inline set. Which setting in the inline set configuration must be selected to allow traffic to pass through uninterrupted when VDB updates are being applied?

A. Tap Mode
B. Strict TCP Enforcement
C. Propagate Link State
D. Snort Fail Open

Answer: D
Explanation:
In inline IPS mode, to ensure that traffic passes through uninterrupted when VDB (Vulnerability Database) updates are being applied, the “Short Fall Open” setting must be configured. This setting allows traffic to continue to flow through the firewall even if there are issues with the inspection process, such as during updates or if the inspection engine fails.
Steps:
In FMC, navigate to the inline set configuration.
Enable the “Short Fall Open” option.
Deploy the configuration to the FTD device.
This ensures that network traffic is not disrupted during updates or other issues with the inspection process.

QUESTION 318
Which two features can be used with Cisco Secure Firewall Threat Defense remote access VPN? (Choose two.)

A. enable Duo two-factor authentication using LDAPS
B. support for Cisco Secure Firewall 4100 Series in cluster mode
C. SSL remote access VPN supports port sharing with other Cisco FTD features using SSL port 443
D. use of license utilization for zero-touch network deployment
E. support for Rapid Threat Containment using RADIUS dynamic authorization

Answer: AE
Explanation:
Cisco Secure Firewall Threat Defense supports integration with external authentication servers, including LDAP and RADIUS, which can be used to enable two-factor authentication solutions such as Duo for enhanced security during VPN login.
FTD remote access VPN supports Rapid Threat Containment features by leveraging RADIUS Change of Authorization (CoA) or dynamic authorization to quickly isolate or remediate compromised VPN clients.
https://www.cisco.com/c/en/us/td/docs/security/secure-firewall/management-center/device-config/710/management-center-device-config-71/vpn-remote-access.html

QUESTION 319
Which rule action is only available in Snort 3?

A. Pass
B. Generate
C. Alert
D. Rewrite

Answer: D
Explanation:
Rewrite is a new rule action introduced in Snort 3 that allows modification of packet contents inline, such as rewriting headers or payloads, which was not possible in Snort 2.x.
Pass, Generate, and Alert are traditional Snort rule actions available in both Snort 2.x and Snort 3.

QUESTION 320
A company is deploying a Cisco Secure IPS device configured in inline mode with a single Interface set that contains four interface pairs. Which two configurations must be implemented to allow the IPS device to uniquely identify packet flows and prevent the reporting of duplicate traffic and false positives? (Choose two.)

A. Set the source SPAN ports to tx only on the switches connected to the IPS interfaces
B. Modify the security zones used by the Cisco Secure IPS device
C. Change the MTU for the inline set to at least 1518
D. Reconfigure access rules to drop all but the first occurrence of the packet
E. Reassign the interface pairs to separate inline sets

Answer: BE
Explanation:
https://www.cisco.com/c/en/us/td/docs/security/firepower/620/configuration/guide/fpmc-config-guide-v62/ips_device_deployments_and_configuration.pdf

Resources From:

1.2025 Latest Braindump2go 300-710 Exam Dumps (PDF & VCE) Free Share:
https://www.braindump2go.com/300-710.html

2.2025 Latest Braindump2go 300-710 PDF and 300-710 VCE Dumps Free Share:
https://drive.google.com/drive/folders/1k8dhswD5V9ioQSctkVOlp0ooiELn46gL?usp=sharing

3.2025 Free Braindump2go 300-710 Exam Questions Download:
https://www.braindump2go.com/free-online-pdf/300-710-VCE-Dumps(265-320).pdf

Free Resources from Braindump2go,We Devoted to Helping You 100% Pass All Exams!